Broan EW5630SS Installationsanleitung PDF herunterladen (Seite 8)

MODELS EW5630SS • EW5636SS

Page 8

MAKE-UP AIR DAMPER

The hood is compatible with Broan Make-Up Air Damper Model

MD6T or Model MD8T (optional). Purchase separately.

Make the connection to the Make-Up Air Damper with low voltage

wiring, as shown. See Make-Up Air Damper instructions for additional

information.

REMOTE CONTROL

This hood is compatible with Broan Radio Frequency (RF) Remote

Control Model BCR1 (optional). Purchase separately.

Conduct the following steps to link the BCR1 remote control with the

hood:

1. On the hood, press and hold the LIGHT button for 3-seconds and

then release it.

2. The blue LED indicators will turn on and off in succession to

indicate the hood is in RF linking mode.

3. When the hood is in the linking mode, press any key on the RF

remote.

4. An audible beep will be heard from the hood and the blue LED’s

will stop blinking, which indicates a successful hood and remote

control link.

• If the remote control did not successfully link with the hood

and no further action is taken, the linking mode will deactivate

after 12 seconds and the blue LED’s will stop blinking

sequentially.

• Refer to the BCR1 instructions for additional information.

Conduct the following steps to erase a remote control link with the

hood:

1. On the hood, press and hold the LIGHT button for 3-seconds

seconds and then release it.

2. The blue LED indicators will turn on and off in succession to

indicate the hood is in RF linking mode.

3. Press and release the OFF button.

4. The blue LED indicators will turn on and off together three times

to confirm the link is erased.

• If the hood did not successfully erase the remote control link and

no further action is taken, the linking mode will deactivate after

12 seconds and the LED’s will stop blinking sequentially.

• Refer to the BCR1 instructions for additional information.

CLEANING & MAINTENANCE

For performance, appearance, and health reasons, clean filter, fan

and grease-laden surfaces. Use only a clean cloth and mild detergent

solution on stainless and painted surfaces.

Clean all-metal filters in the dishwasher using a non-phosphate

detergent. Discoloration of the filter may occur if using phosphate

detergents, or as a result of local water conditions - but this will not

affect filter performance. This discoloration is not covered by the

warranty.

(1)

PUSH IN

(2)

ROTATE

CLOCKWISE

SUCTION

CUP TOOL

HALOGEN

BULB

LAMP SOCKET

BRACKET

SCREWS

LIGHT

PANEL

Clean the non-duct recirculating filter surfaces frequently with a

damp cloth and a mild detergent. DO NOT immerse filters in water

or put in dishwasher. Change the non-duct recirculating filters every

6 months. For replacement non-duct recirculating filters - purchase

S99010365 or Model FILTERE56.

The motor is permanently lubricated and never needs oiling. If the

motor bearings make excessive or unusual noise, replace the blower

assembly with an exact service replacement.

LIGHT BULBS

WARNING

Bulbs may be hot. Always allow bulbs to cool down before removing

them.

Use (2) Halogen Bulbs (included with hood) - 120 V, 35 W, shielded

halogen bulbs - MR16 with GU10 base.

NOTE

Suction Cup Tool (included with hood) can be used to install and

remove light bulbs. Align pins on bulb with large diameter opening

on socket, then push bulb in towards hood and rotate clockwise

until firmly seated. The position of the bulb socket (depth) is

adjustable and may require adjustment when: a) certain brands of

bulbs are difficult to install. b) the bulb protrudes too far below the

light panel.

To change the depth of bulb sockets:

- Remove 2 screws on light panel – set screws aside

- Remove Light Panel.

- Loosen 2 Screws holding Lamp Socket Bracket to Light Panel.

- Adjust socket/bracket to desired depth.

- Re-tighten screws securely.

- Re-attach light panel with 2 screws that were previously set aside.

MAKE-UP AIR DAMPER

HOOD

24V

TRANSFORMER

(INCLUDED)

GRD

DRY CONTA

TERMINAL

BUSHING

FOR LOW

VOLTAGE

CONNECTION

MAKE UP DAMPER CONNECTION

(switched low voltage)

20 GAUGE BELL WIRE FOR LOW

VOLTAGE CONNECTION ON

TOP OF HOOD

120 VAC

60 HZ

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 27 28

Kommentare zu diesen Handbüchern

Keine Kommentare

Broan EW5630SS Installationsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Dunstabzugshauben Broan EW5630SS